Priročnik EMOS EM420B Multimeter

Priročnik

2

MULTIMETER EM420B

Read this owner’s manual thoroughly before use

WARRANTY

This instrument is warranted to be free from defects in material and workmanship

for a period of two year.

Any instrument found defective within two years from the delivery date and returned to

the factory with transportation charges prepaid, will be repaired, adjusted, or replaced

at no charge to the original purchaser. This warranty does not cover expandable items

such as batteries or fuse. If the defect has been cause by a misuse or abnormal operation

conditions, the repair will be billed at a nominal cost.

SAFETY INFORMATION

The multimeter has been designed according to IEC-61010 concerning electronic meas-

uring instruments with a measurement category (CAT II 600V) and Pollution degree2

ELECTRICAL SYMBOLS

AC (Alternating Current)

DC (Direct Current)

DC or AC(alternating current or directive current)

Important safety information. Refer to the manual

Dangerous voltage may be present.

Earth ground

Fuse

Conforms to European Union directives

Double insulated.

Low battery

Diode

The maximum values is being held

The display data is being held

Fahrenheit

Centigrade

Continuity test

Measurement with clamp (optional), widening the eld of applica-

tions of the meter

Autorange

– Danger of electrical injury

Warning, Danger. Please pay attention to the passages of this manual

where this symbol is used.

WARNING

To avoid possible electric shock or personal injury, follow these guidelines:

• Do not use the meter if it is damaged. Before you use the meter, inspect the case.

Pay particular attention to the insulation surrounding the connectors.

• Inspect the test leads for damaged insulation or exposed metal. Check the test

leads for continuity. Replace damaged test leads before you use the meter.

• Do not use the meter if it operates abnormally. Protection may be impaired. When

in doubt, have the meter serviced.

• Do not operate the meter around explosive gas, vapor, or dust.

• Do not apply more than the rated voltage, as marked on the meter, between

terminals or between any terminal and earth ground.

• Before use, verify the meter’s operation by measuring a known voltage.

• When measuring current, turn o circuit power before connecting the meter in

the circuit. Remember to place the meter in the circuit. Remember to place the

meter in series with the circuit.

• When servicing the meter, use only specied replacement parts.

• Use with caution when working above 30V ac rms, 42V peak, or 60V dc. Such

voltages pose a shock hazard.

• When using the probes, keep your ngers behind the nger guards on the probes.

• Connect the common test lead before you connect the live test lead. When you

disconnect test leads, disconnect the live test lead rst.

• Remove the test leads from the meter before you open the case.

• Do not operate the meter with the cover removed or loosened.

• To avoid false readings, which could lead to possible electric shock or personal

injury, replace the batteries as soon as the low battery indicator appears.

• Do not use the test leads to measure the voltage which is more than 600V or the

current which is more than 10A.

• Remaining endangerment: When an input terminal is connected to dangerous live

potentional it is to be noted than this potential at all other terminals can occur!

• CATII-Measurement Category II is for measurements performed on circuits directly

connected to low voltage installation. Do not use the meter for measurements

within Measurement Categories III and IV.

CAUTION

To avoid possible damage to the meter or to the equipment under test, follow

these guidelines:

• Disconnect circuit power and discharge all high voltage capacitors before testing

resistance, continuity, diodes, or capacitance.

• Use the proper terminals, function, and range for your measurements.

• Before measuring current, check the meter’s fuse and turn power OFF to the circuit

before connecting the meter to the circuit.

• Before rotating Function / Range switch to change functions, disconnect test leads

from the circuit under test.

• Before inserting transistor to the adapter , always be sure all the test leads have

been removed from the meter

• Remove test leads from the meter before opening the battery cover or the case.

MAINTENANCE

To continue protection against re, replace fuse only with the specied voltage and

currents rating: F 250 mA L 250V, fast action.

To clean the meter, use a damp cloth and mild detergent only, do not use abrasives

or solvents on it.

GENERAL DESCRIPTION

This digital multimetr is compact 3,5 digits digital multimeter for measuring DC and

AC voltage, DC and AC current, resistance, temperature, diode, transistor, continuity,

capacitance ( only EM420B)and battery(only EM420A). It has the functions of polarity

indication, data hold, maximum value hold, overrange indicator and automatic power-

o. It can be operated easily and is ideal instrument tool.

Instruction

1 DISPLAY – 3,5 digit LCD with a max reading of 1999

2 RANGE button – The meter defaults to the autorange mode when you measure

the voltage, current or resistance. When the meter is in the autorange mode, AUTO

i s displayed.

To enter and exit the manual range mode:

a) Press RANGE button – The meter enters the manual range mode and the symbol

AUTO turns o.

Each press of the RANGE button increments the range. Then the highest range is

reached, the meter wraps to lowest range

b) To exit the manual range mode, press and hold down the RANGE button for

2 seconds, the meter returns to the autorange mode and the symbol AUTO is

displayed again.

3 FUNC. button – When you measure the current, pressing this button will switch

the meter between DC function and AC function.

When you measure the temperature, pressing this button will switch the meter

between °F mode and °C mode

When you measure the diode or the continuity functions.

4 POWER switch – It can be used to turn on/o the meter.

5 FUNCTION/RANGE SWITCH – This switch can be used to select desired function

and range.

6 10A Jack – Plug-in connector for the red test lead for current (200 mA ~10 A)

measurement.

7 COM Jack – Plug-in connector for black(negative) test lead.

8 INPUT Jack – Plug-in connector for the red test lead for all measurement except

current(≥200mA) measurements.

9

Button – To turn on or o the backlight, press and hold this button for about

2 seconds. The backlight will turns o automatically about 15 seconds later after

you turn on it.

10

Button – After pressing the button, the present reading is held on the

display, meanwhile is displayed on the LCD as an indicator. To exit th Hold Mode,

press the button again and the indicator will disappear.

11

Button – The hold the maximum value, press this button and will appear

as an indicator, the meter will hold the maximum of all readings taken since the

button was pressed. To exit the maximum value hold mode, just press this button

again and will disappear.

In some ranges, the maximum value hold mode is not available.

GENERAL SPECIFICATION

Display: LCD, 1999 counts, updates 2–3 times/sec

Overrange Indications: OL shown on display

Battery: 3× 1,5V, AAA

Polarity Indication: „–„ displayed atomatically

Low Battery Indication: shown on display

GB

Ocena

Več o tem priročniku

Zavedamo se, da je lepo imeti papirni priročnik za vaš EMOS EM420B Multimeter. Priročnik lahko vedno prenesete z naše spletne strani in ga natisnete sami. Če želite imeti originalni priročnik, priporočamo, da kontaktirate EMOS. Morda bodo lahko zagotovili originalni priročnik. Ali iščete priročnik za vaš EMOS EM420B Multimeter v drugem jeziku? Na naši domači strani izberite želeni jezik in poiščite številko modela, da preverite, ali je na voljo.

Specifikacije

Vsi priročniki za EMOS Multimetri
Več priročnikov za Multimetri

Podobni izdelki

Priročnik

EMOS MD-220 Multimeter

Priročnik

FERM MMM1008 Multimeter

Priročnik

FERM MMM1007 Multimeter

Priročnik

Powerfix IAN 89117 Multimeter

Sorodne kategorije