Priročnik FERM AGM1001 Kotna brusilka

Potrebujete priročnik za vaš FERM AGM1001 Kotna brusilka? Spodaj si lahko brezplačno ogledate in prenesete PDF priročnik v slovenščini. Ta izdelek ima trenutno 4 pogosto zastavljeni vprašanji, 0 komentarjev in ima 0 glasov. Če to ni priročnik, ki ga želite, nas kontaktirajte.

Ali je vaš izdelek okvarjen in v priročniku ne najdete rešitve? Obiščite Repair Café za brezplačno popravilo.

Priročnik

Loading…


       ,
     .
   Ferm   
     
 .   
      
    .

     
  ,     
.     
     .
    ,   ,
  .   
,  , ,  .
      
 .

o     .

     ,
      ,
     
Ferm.
        
     
    .

         ,
    . 
      
.     
  .

     
    .
      
    
   :
EN-50144-1, prEN50144-2-3,
EN-55014-1, EN-55014-2,
EN61000-3-2, EN61000-3-3,
      
:
98/37EEC
73/23EEC
89/336EEC
 17-12-2002
GENEMUIDEN NL
W. Kamphof
Quality department
CE
ı
 
(
GR
)
Ferm 57
Ensure that mounted wheels and points are fitted in
accordance with the manufacturer’s instructions.
Ensure that blotters are used when they are provided
with the bonded abrasive product and when they are
required.
If a guard is supplied with the tool never use the tool
without such a guard.
For tools intended to be fitted with threaded hole
wheel, ensure that the thread in the wheel is long
enough to accept the spindle length.
Ensure that ventilation openings are kept clear when
working in dusty conditions. If it should become nes-
sesary to clear dust, first disconnect the tool from the
mains supply (use non metallic objects) and avoid
damaging internal parts.
Though poor conditions of the electrical mains,
shortly voltage drops can appear when starting the
equipment. This can influence other equipment (eq.
blinking of a lamp). If the mains-impedance Zmax
<0.348 Ohm, such disturbances are not expected. (In
case of need, you may contact your local supply aut-
hority for further information.
ELECTRICAL SAFETY
Always check that the power supply corresponds to
the voltage on the rating plate.
Your machine is double insulated in accordance
with EN50144; therefore no earthwire is required.
Replacing cables or plugs
Immediately throw away old cables or plugs when they
have been replaced by new ones. It is dangerous to insert
the plug of a loose cable in the wall outlet.
Using extension cables
Only use an approved extension cable suitable for the
power input of the machine. The minimum conductor
size is 1.5 mm
2
. When using a cable reel always unwind
the reel completely.
MOUNTING ACCESSORIES
Fig.B
Prior to mounting an accessory always unplug the
tool.
REMOVING AND MOUNTING THE GUARD
Replace the guard only with one of sheet steel or mate-
rial of equal strength.
DISASSEMBLY
Remove the flange nut and the flange from the spindle
(5).
Unscrew the 4 screws with washers (3 + 4) and
remove the second flange.
Remove the machine’s protective hood.
ASSEMBLY
Put the protective hood (1) on the machine.
Place the second flange (2) on the spindle (5) and
slightly tighten the screws with washers (3 + 4).
Turn the protective hood to the position indicated in
the drawing and completely tighten the screws.
Put the flange nut and the flange back on the spindle
(5).
MOUNTING A GRINDING DISC
Fig.C
Use grinding discs of the correct dimension. Use fibre
reinforced grinding discs only. The grinding disc must not
touch the edge of the guard.
Press the spindle lock and turn the spindle (9) until it
engages in the lock. Keep the spindle lock pressed
during this procedure.
Remove the flange nut (12) from the spindle using the
spanner (11).
Position the grinding disc (7) on the flange (5).
Place the flange nut on the spindle an tighten it using
the spanner.
Release the spindle lock and check that the spindle is
unlocked by rotating it.
MOUNTING THE SIDE HANDLE
The side handle can be used for both left-hand and right-
hand control.
Fasten the side handle (Fig. A-3) for left-hand opera-
tion on the right-hand side of the machine.
Fasten the side handle for right-hand operation on
the left-hand side of the machine.
Fasten the side handle for upright working at the top
of the machine.
Make sure that the side handle is fastened properly
and cannot loosen unexpectedly.
4 Ferm
Prenesi priročnik v slovenščini (PDF, 0.99 MB)
(Upoštevajte okolje in natisnite ta priročnik le, če je res potrebno)

Loading…

Ocena

Povejte nam, kaj menite o FERM AGM1001 Kotna brusilka, tako da oddate oceno izdelka. Ali želite deliti svoje izkušnje z izdelkom ali postaviti vprašanje? Oddajte komentar na dnu strani.
Ali ste zadovoljni z FERM AGM1001 Kotna brusilka?
Da Ne
Bodite prvi, ki boste ocenili ta izdelek
0 glasovi

Pridružite se pogovoru o tem izdelku

Tukaj lahko delite svoje mnenje o FERM AGM1001 Kotna brusilka. Če imate vprašanje, najprej natančno preberite priročnik. Zahtevo za priročnik lahko opravite z uporabo našega kontaktnega obrazca.

Več o tem priročniku

Zavedamo se, da je lepo imeti papirni priročnik za vaš FERM AGM1001 Kotna brusilka. Priročnik lahko vedno prenesete z naše spletne strani in ga natisnete sami. Če želite imeti originalni priročnik, priporočamo, da kontaktirate FERM. Morda bodo lahko zagotovili originalni priročnik. Ali iščete priročnik za vaš FERM AGM1001 Kotna brusilka v drugem jeziku? Na naši domači strani izberite želeni jezik in poiščite številko modela, da preverite, ali je na voljo.

Specifikacije

Blagovna znamka FERM
Model AGM1001
Kategorija Kotne brusilke
Vrsta datoteke PDF
Velikost datoteke 0.99 MB

Vsi priročniki za FERM Kotne brusilke
Več priročnikov za Kotne brusilke

Pogosto zastavljena vprašanja o FERM AGM1001 Kotna brusilka

Naša podporna ekipa išče uporabne informacije o izdelkih in odgovore na pogosta vprašanja. Če v pogosto postavljenih vprašanjih odkrijete nenatančnost, nam to sporočite prek obrazca za stik.

Na katerih površinah lahko uporabljam kotno brusilko? Potrjeno

Kotne brusilke so najprimernejše za uporabo na kovinah ali kamnu.Proizvajajo veliko toplote, zato so manj primerne za uporabo na lesu ali plastiki.

To je bilo koristno (63) Preberi več

Ali moram nositi zaščito za sluh pri uporabi kotne brusilnice? Potrjeno

Da, morali bi. Čeprav se količina hrupa, ki ga proizvaja kotna brusilka, med različnimi znamkami in modeli lahko razlikuje, lahko dolgotrajna izpostavljenost glasnemu hrupu povzroči trajne poškodbe sluha. Zato je dobro nositi zaščito za sluh.

To je bilo koristno (16) Preberi več

Ali moram pri uporabi kotne brusilne naprave nositi zaščito za oči? Potrjeno

Da. Majhni delci lahko med brušenjem poletijo navzgor. Ko ti zadenejo oko, lahko povzročijo trajne poškodbe oči. Zato je vedno treba nositi zaščito za oči.

To je bilo koristno (14) Preberi več

Ali lahko električno orodje shranim v lopi ali garaži? Potrjeno

Na splošno lahko električno orodje shranite v lopi ali garaži, tudi če tam včasih zmrzne. Za življenjsko dobo električnega orodja pa je bolje, da ga hranite v suhem prostoru brez večjih temperaturnih nihanj. V lopi ali garaži lahko razlike v temperaturi povzročijo nastanek kondenza, ki lahko povzroči rjo. Poleg tega orodja, ki delujejo na baterije, delujejo krajše in se pri zelo nizkih temperaturah ne polnijo tako dobro. Da bi bili prepričani, kako je treba vaše električno orodje shraniti, vedno temeljito preberite uporabniški priročnik.

To je bilo koristno (5) Preberi več
Priročnik FERM AGM1001 Kotna brusilka

Podobni izdelki

Sorodne kategorije