Home > Naredi sam > Mešalniki za cement > FERM Mešalniki za cement > FERM PMM1006 Mešalnik za cement

Priročnik FERM PMM1006 Mešalnik za cement

Potrebujete priročnik za vaš FERM PMM1006 Mešalnik za cement? Spodaj si lahko brezplačno ogledate in prenesete PDF priročnik v slovenščini. Ta izdelek ima trenutno 1 pogosto zastavljeno vprašanje, 0 komentarjev in ima 0 glasov. Če to ni priročnik, ki ga želite, nas kontaktirajte.

Ali je vaš izdelek okvarjen in v priročniku ne najdete rešitve? Obiščite Repair Café za brezplačno popravilo.

Priročnik

Ferm

prevent at the same time when switching on the

machine.

As a result of the machine’s reduced starting

current, a 16 A fuse is sufficient.

No load speed reduction

The electronic control reduces the no-load speed

of the machine which results in reduced noise and

wear of motor and gear.

Speed pre-selection

With the speed control (3) the speed can be

continuously pre-selected: the necessary speed is

dependent on the type of material to be mixed. It is

recommended that it be confirmed with a practical

trial.

Speed selection

Two rpm ranges can be pre-selected with the

speed selector switch (4):

Gear 1 180-380 r/min

Gear 2 300-650 r/min

The necessary speed depends on the type of the

material mixed and it is recommended to verify it

by a practical test.

Constant electronics

The constant electronics keeps the speed

between no-load and load nearly constant and

ensures uniform mixing of the materials.

Electronic overload protection

In case that the machine is extremely overloaded,

an electronic overload protection protects the

motor from damage. In this case, the motor stops

and restarts only after the feeding pressure is

reduced.

Temperature-dependant overload protection

To protect the motor from overheating at extreme

permanent load, it is switched off by the protective

electronic system when a critical temperature is

reached.

After a cooling-down period of approx. 3-5 min.,

de machine is again ready for use and can be fully

loaded.

When the machine is warmed by use, the

temperature-dependent overload protection reacts

earlier as a result.

6. Service & maintenance

Make sure that the machine is not live

when carrying out maintenance work on

the motor.

This machine has been designed to operate

over a long period of time with a minimum of

maintenance. Continuous satisfactory operation

depends upon proper machine care and regular

cleaning.

• The ventilating slots on the motor casing

should be cleaned out from time to time.

• After 100 hours: check carbon brushes

• After 200 hours: renew the grease filling in the

gearbox

Cleaning

Regularly clean the device’s casing with a soft

cloth, preferably after each use. Keep the fan slits

free of dust and dirt. Remove stubborn dirt using a

soft cloth, dampened with soapy water. Do not use

solvents such as benzene, alcohol, ammonia, etc,

which might damage the plastic parts.

Lubrication

The device does not need any additional

lubrication.

Defects

If a defect appears due to a part wearing out,

please contact the service center on the warranty

card. Separately you will find an exploded view

showing the parts that can be ordered.

Environment

To prevent damage during transport, the appliance

is delivered in a solid packaging which consists

largely of reusable material. Therefore please

make use of options for recycling the packaging.

Damaged and/or disposed of electrical or

electronic devices must be dropped off at

recycling stations intended for that

purpose.



Read the warranty conditions on the separately

supplied warranty card.

Prenesi priročnik v slovenščini (PDF, 2.1 MB)

(Upoštevajte okolje in natisnite ta priročnik le, če je res potrebno)

Ocena

Povejte nam, kaj menite o FERM PMM1006 Mešalnik za cement, tako da oddate oceno izdelka. Ali želite deliti svoje izkušnje z izdelkom ali postaviti vprašanje? Oddajte komentar na dnu strani.

Ali ste zadovoljni z FERM PMM1006 Mešalnik za cement?
Da Ne

Bodite prvi, ki boste ocenili ta izdelek

0 glasovi

Pridružite se pogovoru o tem izdelku

Tukaj lahko delite svoje mnenje o FERM PMM1006 Mešalnik za cement. Če imate vprašanje, najprej natančno preberite priročnik. Zahtevo za priročnik lahko opravite z uporabo našega kontaktnega obrazca.

Več o tem priročniku

Zavedamo se, da je lepo imeti papirni priročnik za vaš FERM PMM1006 Mešalnik za cement. Priročnik lahko vedno prenesete z naše spletne strani in ga natisnete sami. Če želite imeti originalni priročnik, priporočamo, da kontaktirate FERM. Morda bodo lahko zagotovili originalni priročnik. Ali iščete priročnik za vaš FERM PMM1006 Mešalnik za cement v drugem jeziku? Na naši domači strani izberite želeni jezik in poiščite številko modela, da preverite, ali je na voljo.

Specifikacije

Blagovna znamka	FERM
Model	PMM1006
Kategorija	Mešalniki za cement
Vrsta datoteke	PDF
Velikost datoteke	2.1 MB

Vsi priročniki za FERM Mešalniki za cement
Več priročnikov za Mešalniki za cement

Pogosto zastavljena vprašanja o FERM PMM1006 Mešalnik za cement

Naša podporna ekipa išče uporabne informacije o izdelkih in odgovore na pogosta vprašanja. Če v pogosto postavljenih vprašanjih odkrijete nenatančnost, nam to sporočite prek obrazca za stik.

Ali lahko električno orodje shranim v lopi ali garaži? Potrjeno

Na splošno lahko električno orodje shranite v lopi ali garaži, tudi če tam včasih zmrzne. Za življenjsko dobo električnega orodja pa je bolje, da ga hranite v suhem prostoru brez večjih temperaturnih nihanj. V lopi ali garaži lahko razlike v temperaturi povzročijo nastanek kondenza, ki lahko povzroči rjo. Poleg tega orodja, ki delujejo na baterije, delujejo krajše in se pri zelo nizkih temperaturah ne polnijo tako dobro. Da bi bili prepričani, kako je treba vaše električno orodje shraniti, vedno temeljito preberite uporabniški priročnik.

To je bilo koristno (8) Preberi več