Home > Naredi sam > Povratne žage > FERM Povratne žage > FERM RSM1018 Povratna žaga

Priročnik FERM RSM1018 Povratna žaga

Potrebujete priročnik za vaš FERM RSM1018 Povratna žaga? Spodaj si lahko brezplačno ogledate in prenesete PDF priročnik v slovenščini. Ta izdelek ima trenutno 3 pogosto zastavljeni vprašanji, 0 komentarjev in ima 0 glasov. Če to ni priročnik, ki ga želite, nas kontaktirajte.

Ali je vaš izdelek okvarjen in v priročniku ne najdete rešitve? Obiščite Repair Café za brezplačno popravilo.

Priročnik

4. OPERATION

Always follow the safety notes and the

relevant safety code.

Make sure that the saw blade does not

rest on or touch any objects when the

machine is switched on.

Switching on and off

Fig. A

• To switch on the machine, press the on/off

switch (3).

• To switch the machine to continuous mode,

keep the on/off switch (3) pressed and

simultaneously press the lock-on button (4).

• To switch off the machine, release the on/off

switch (3).

Sawing tips

• Adjust saw blade and stroke rate to suit the

material to be processed. For right radius curves

it is best to use a narrow saw blade. Apply

coolant or lubricant to deal with the fluttering

produced along the cut line when sawing metal.

• Check wood, chip boards, building materials

etc, for foreign bodies (nails, screws etc.),

before sawing and remove them, if necessary.

• Clamp material well. Do not support the

workpiece with hand or foot. Do not touch

objects or the floor with the saw running

(danger of backlash).

• Put the footplate on the surface of the

workpiece, and saw through it with constant

contact pressure or feed. If the saw blade

seizes switch the machine off immediately.

Spread the gap with a suitable tool and pull out

the saw blade.

• After finishing work, switch off the machine

and only put down after it has come to a

complete standstill.

Plunge cutting

Fig. C

• Plunge cutting may only be used on soft

materials such as wood, aerated concrete,

gypsum plaster boards, etc.

• However, this requires a certain practise and is

only possible with short saw blades.

• Place the saw onto the workpiece and switch it

on.

• Ensure that the bottom edge of the footplate

rests on the workpiece surface as shown.

• Slowly saw into the workpiece at an angle,

moving the saw to a vertical position and

continue to saw along the cutting line.

• Switch the saw off and lift off the workpiece

when the work is complete.

Flush sawing

• Elastic bi-metal saw blades allow you to saw

protruding objects (e,g, water pipes, iron bars,

etc,) nearby the wall.

• Apply the saw blade directly to the wall and

bend slightly so that the footplate rests against

the wall.

• Switch the machine on and saw off the

workpiece keeping constant lateral pressure

against the wall.

5. SERVICE & MAINTENANCE

Make sure that the machine is not live

when carrying out maintenance work on

the motor.

The machines have been designed to operate

over a long period of time with a minimum of

maintenance. Continuous satisfactory operation

depends upon proper machine care and regular

cleaning.

Cleaning

Keep the ventilation slots of the machine clean to

prevent overheating of the engine. Regularly clean

the machine housing with a soft cloth, preferably

after each use. Keep the ventilation slots free from

dust and dirt. If the dirt does not come off use a

soft cloth moistened with soapy water. Never use

solvents such as petrol, alcohol, ammonia water,

etc. These solvents may damage the plastic parts.

Lubrication

The machine requires no additional lubrication.

Faults

Should a fault occur, e.g. after wear of a part,

please contact the service address on the

warranty card. In the back of this manual you find

an exploded view showing the parts that can be

ordered.

Ocena

Povejte nam, kaj menite o FERM RSM1018 Povratna žaga, tako da oddate oceno izdelka. Ali želite deliti svoje izkušnje z izdelkom ali postaviti vprašanje? Oddajte komentar na dnu strani.

Ali ste zadovoljni z FERM RSM1018 Povratna žaga?
Da Ne

Bodite prvi, ki boste ocenili ta izdelek

0 glasovi

Pridružite se pogovoru o tem izdelku

Tukaj lahko delite svoje mnenje o FERM RSM1018 Povratna žaga. Če imate vprašanje, najprej natančno preberite priročnik. Zahtevo za priročnik lahko opravite z uporabo našega kontaktnega obrazca.

Več o tem priročniku

Zavedamo se, da je lepo imeti papirni priročnik za vaš FERM RSM1018 Povratna žaga. Priročnik lahko vedno prenesete z naše spletne strani in ga natisnete sami. Če želite imeti originalni priročnik, priporočamo, da kontaktirate FERM. Morda bodo lahko zagotovili originalni priročnik. Ali iščete priročnik za vaš FERM RSM1018 Povratna žaga v drugem jeziku? Na naši domači strani izberite želeni jezik in poiščite številko modela, da preverite, ali je na voljo.

Specifikacije

Blagovna znamka	FERM
Model	RSM1018
Kategorija	Povratne žage
Vrsta datoteke	PDF
Velikost datoteke	8.31 MB

Vsi priročniki za FERM Povratne žage
Več priročnikov za Povratne žage

Pogosto zastavljena vprašanja o FERM RSM1018 Povratna žaga

Naša podporna ekipa išče uporabne informacije o izdelkih in odgovore na pogosta vprašanja. Če v pogosto postavljenih vprašanjih odkrijete nenatančnost, nam to sporočite prek obrazca za stik.

Za kaj lahko uporabljam povratno žago? Potrjeno

Zaradi rezila, ki ga je mogoče zamenjati, so te žage primerne za uporabo na skoraj vseh materialih.Pogosto se uporabljajo za vgradne in sanitarne storitve.

To je bilo koristno (42) Preberi več

Ali moram pri uporabi batne žage nositi zaščito za oči? Potrjeno

Da. Majhni delci lahko med žaganjem poletijo navzgor. Ko ti zadenejo oko, lahko povzročijo trajne poškodbe oči. Zato je vedno treba nositi zaščito za oči.

To je bilo koristno (24) Preberi več

Ali lahko električno orodje shranim v lopi ali garaži? Potrjeno

Na splošno lahko električno orodje shranite v lopi ali garaži, tudi če tam včasih zmrzne. Za življenjsko dobo električnega orodja pa je bolje, da ga hranite v suhem prostoru brez večjih temperaturnih nihanj. V lopi ali garaži lahko razlike v temperaturi povzročijo nastanek kondenza, ki lahko povzroči rjo. Poleg tega orodja, ki delujejo na baterije, delujejo krajše in se pri zelo nizkih temperaturah ne polnijo tako dobro. Da bi bili prepričani, kako je treba vaše električno orodje shraniti, vedno temeljito preberite uporabniški priročnik.

To je bilo koristno (11) Preberi več