Priročnik Greenworks GD40CS18 Motorna žaga

Priročnik

1 DESCRIPTION

1.1 OVERVIEW

Figure 1-22

1

Guide bar cover

2

Front handle

guard / chain brake

3

Front handle

4

Lock out button

5

Trigger

6

Oil tank cap

7

Oil indicator

8

Spike bumpers

9

Saw chain

10

Guide bar

11

Wrench

12

Rear handle

13

Chain tension

screw

14

Chain cover

15

Chain cover nuts

16

Bolt for saw chain

tension

17

Sprocket

18

Battery release

button

19

Oil outlet

20

Bar groove

21

Chain drive links

22

Cutter

23

Felling direction

24

Danger zone

25

Escape route

26

Direction of fall

27

Notch

28

Felling back cut

29

Hinge

30

Limb cut

31

Keep work off

ground leave

support limbs until

log is cut

32

Log supported

along the entire

length

33

Cut from top (over

buck) avoid cutting

earth

34

Log supported one

end

35

Under buck

36

Over buck

37

Log supported both

ends

38

Bucking a log

39

Stand on uphill side

when cutting

because log may

roll

2 SAFETY

WARNING

Make sure that you do/obey all safety instructions.

Refer to Safety Manual.

3 INSTALLATION

WARNING

Do not change or make accessories that are not

recommended by the manufacturer.

WARNING

Do not put in the battery pack until you assemble all

the parts.

3.1 UNPACK THE MACHINE

WARNING

Make sure that you correctly assemble the machine

before use.

WARNING

• If the parts have damage, do not use the machine.

• If you do not have all the parts, do not operate the

machine.

• If the parts are damaged or missing, speak to the

service center.

1. Open the package.

2. Read the documentation in the box.

3. Remove all the unassembled parts from the box.

4. Remove the machine from the box.

5. Discard the box and package in compliance with

local regulations.

3.2 ASSEMBLE THE GUIDE BAR AND

THE CHAIN

Figure 1-7.

1. Remove the chain cover nuts with the wrench.

2. Remove the chain cover.

3. Put the chain drive links into the bar groove.

4. Put the chain cutters in the direction of the chain

operation.

5. Put the chain in position and make sure that the

loop is behind the guide bar.

6. Hold the chain and bar.

7. Put the chain loop around the sprocket.

8. Make sure the chain tension pin hole on the guide

bar fits correctly with the bolt.

9. Install the chain cover.

10. Tighten the chain. Refer to

Adjust the chain tension.

11. Tighten the nuts when the chain is well tensioned.

NOTE

If you start the chain saw with a new chain, have a test

for 2-3 minutes. A new chain gets longer after the first

use, examine the tension and tighten the chain if

necessary.

3.3 INSTALL THE BATTERY PACK

Figure 2

5

English

EN

Ocena

Več o tem priročniku

Zavedamo se, da je lepo imeti papirni priročnik za vaš Greenworks GD40CS18 Motorna žaga. Priročnik lahko vedno prenesete z naše spletne strani in ga natisnete sami. Če želite imeti originalni priročnik, priporočamo, da kontaktirate Greenworks. Morda bodo lahko zagotovili originalni priročnik. Ali iščete priročnik za vaš Greenworks GD40CS18 Motorna žaga v drugem jeziku? Na naši domači strani izberite želeni jezik in poiščite številko modela, da preverite, ali je na voljo.

Specifikacije

Vsi priročniki za Greenworks Motorne žage
Več priročnikov za Motorne žage

Pogosto zastavljena vprašanja o Greenworks GD40CS18 Motorna žaga

Naša podporna ekipa išče uporabne informacije o izdelkih in odgovore na pogosta vprašanja. Če v pogosto postavljenih vprašanjih odkrijete nenatančnost, nam to sporočite prek obrazca za stik.

Podobni izdelki

Priročnik

Greenworks G24CS25 Motorna žaga

Priročnik

Greenworks GD60CS40 Motorna žaga

Priročnik

Greenworks G40CS30 Motorna žaga

Priročnik

Greenworks GD40CS40 Motorna žaga

Priročnik

Greenworks CD40CS15 Motorna žaga

Priročnik

Greenworks GD40TCS Motorna žaga

Priročnik

Cramer 82PST Motorna žaga

Priročnik

Parkside IAN 415941 Motorna žaga

Sorodne kategorije