Home > Naredi sam > Krožne žage > Hikoki Krožne žage > Hikoki C 6U3 Krožna žaga

Priročnik Hikoki C 6U3 Krožna žaga

Potrebujete priročnik za vaš Hikoki C 6U3 Krožna žaga? Spodaj si lahko brezplačno ogledate in prenesete PDF priročnik v slovenščini. Ta izdelek ima trenutno 3 pogosto zastavljeni vprašanji, 0 komentarjev in ima 0 glasov. Če to ni priročnik, ki ga želite, nas kontaktirajte.

Ali je vaš izdelek okvarjen in v priročniku ne najdete rešitve? Obiščite Repair Café za brezplačno popravilo.

Priročnik

English

Riving knife function

a) Use the appropriate saw blade for the riving knife.

For the riving knife to function, the body of the blade

must be thinner than the riving knife and the cutting

width of the blade must be wider than the thickness of

the riving knife.

b) Adjust the riving knife as described in this

instruction manual.

Incorrect spacing, positioning and alignment can make

the riving knife ineﬀ ective in preventing kickback.

c) Always use the riving knife except when plunge

cutting.

The riving knife must be replaced after plunge cutting.

The riving knife causes interference during plunge

cutting and can create kickback.

d) For the riving knife to work, it must be engaged in

the workpiece.

The riving knife is ineﬀ ective in preventing kickback

during short cuts.

e) Do not operate the saw if the riving knife is bent.

Even a light interference can slow the closing rate of a

guard.

ADDITIONAL SAFETY WARNINGS

1. Use only blade diameter speciﬁ ed on the machine.

2. Do not use any abrasive wheel.

3. Do not use saw blades which are deformed or cracked.

4. Do not use saw blades made of high speed steel.

5. Do not use saw blades which do not comply with the

characteristics speciﬁ ed in these instructions.

6. Do not stop the saw blades by lateral pressure on the

disc.

7. Always keep the saw blades sharp.

8. Ensure that the lower guard moves smoothly and freely.

9. Never use the circular saw with its lower guard ﬁ xed in

the open position.

10. Ensure that the retraction mechanism of the guard

system operates correctly.

11. The saw blades body must be thinner than the riving

knife and the width of cut, or kerf (with teeth set) must be

greater than the thickness of the riving knife.

12. Never operate the circular saw with the saw blade turned

upward or to the side.

13. Ensure that the material is free of foreign matters such as

nails.

14. The riving knife should always be used except when

plunging in the middle of the workpiece.

15. Disconnect the plug from the receptacle before carrying

out any adjustment, servicing or maintenance.

16. For models C6BU3, C6BUM, C7BU3 and C7BUM, be

careful of brake kickback.

C6BU3, C6BUM, C7BU3 and C7BUM models feature an

electric brake that functions when the switch is released.

As there is some kickback when the brake functions, be

sure to hold the main body securely.

17. Sparks can sometimes appear caused by braking

operation when the switch is turned oﬀ since C6BU3,

C6BUM, C7BU3 and C7BUM models employ electric

brakes. Be informed, however, that this phenomenon is

not a machine trouble.

18. For models C6BU3, C6BUM, C7BU3 and C7BUM,

when the brake becomes ineﬀ ective, replace the carbon

brushes with new ones.

19. Ensure that the power source to be utilized conforms

to the power requirements speciﬁ ed on the product

nameplate.

20. Before the tool is plugged in to the receptacle, ensure

that the power switch is in the OFF position.

If the plug is connected to a receptacle while the power

switch is in the ON position, the power tool will start

operating immediately, which could cause a serious

accident.

21. When the work area is removed from the power source,

use an extension cord of suﬃ cient thickness and rated

capacity. The extension cord should be kept as short as

practicable.

22. Since the saw blade will extend beyond the lower surface

of the lumber, place the lumber on a workbench when

cutting. If a square block is utilized as a workbench,

select level ground to ensure it is properly stabilized. An

unstable workbench will result in hazardous operation.

(Fig. 3)

To avoid possible accident, always ensure that the

portion of lumber remaining after cutting is securely

anchored or held in position.

23. Should knob remain loosened, it will create a very

hazardous situation. Always thoroughly clamp it. (Fig. 4)

24. It is very hazardous to allow wing bolt to remain loosened.

Always thoroughly clamp it. (Fig. 5)

25. Prior to cutting operation, make sure the material you

are going to cut. If the material to be cut is expected to

generate harmful / toxic dusts, make sure the dust bag

or appropriate dust extraction system is connected with

dust outlet tightly.

Wear the dust mask additionally, if available.

○ Before starting to saw, conﬁ rm that the saw blade

has attained full-speed revolution.

○ Should the saw blade stop or make an abnormal

noise while operating, promptly turn OFF the switch.

○ Always take care in preventing the power cord from

coming near to the revolving saw blade.

○ Using the circular saw with the saw blade facing

upwards or sideways is very hazardous. Such

uncommon applications should be avoided.

○ When cutting materials, always wear protective

glasses.

○ When ﬁ nished with a job, pull out the plug from the

receptacle.

26. After having attached the saw blade, reconﬁ rm that the

lock lever is ﬁ rmly secured in the prescribed position.

27. Models C6U3, C6BU3, C7U3 and C7BU3 are equipped

with a blower function. However, do not use the tool for

the blower function only. (Fig. 8

)

28. Check that there are no nicks or scratches in the cord.

29. Check the exterior and ensure that there is no damage.

30. Use a chip saw that is for cutting wood.

31. Use a chip saw with a displayed speed that is equal to or

higher than the rotation speed displayed on the tool.

32. Do not leave the saw placed on top of the guide rail.

0000Book̲C6U3.indb40000Book̲C6U3.indb4 2017/12/0113:15:502017/12/0113:15:50

Ocena

Povejte nam, kaj menite o Hikoki C 6U3 Krožna žaga, tako da oddate oceno izdelka. Ali želite deliti svoje izkušnje z izdelkom ali postaviti vprašanje? Oddajte komentar na dnu strani.

Ali ste zadovoljni z Hikoki C 6U3 Krožna žaga?
Da Ne

Bodite prvi, ki boste ocenili ta izdelek

0 glasovi

Pridružite se pogovoru o tem izdelku

Tukaj lahko delite svoje mnenje o Hikoki C 6U3 Krožna žaga. Če imate vprašanje, najprej natančno preberite priročnik. Zahtevo za priročnik lahko opravite z uporabo našega kontaktnega obrazca.

Več o tem priročniku

Zavedamo se, da je lepo imeti papirni priročnik za vaš Hikoki C 6U3 Krožna žaga. Priročnik lahko vedno prenesete z naše spletne strani in ga natisnete sami. Če želite imeti originalni priročnik, priporočamo, da kontaktirate Hikoki. Morda bodo lahko zagotovili originalni priročnik. Ali iščete priročnik za vaš Hikoki C 6U3 Krožna žaga v drugem jeziku? Na naši domači strani izberite želeni jezik in poiščite številko modela, da preverite, ali je na voljo.

Specifikacije

Blagovna znamka	Hikoki
Model	C 6U3
Kategorija	Krožne žage
Vrsta datoteke	PDF
Velikost datoteke	11.94 MB

Vsi priročniki za Hikoki Krožne žage
Več priročnikov za Krožne žage

Pogosto zastavljena vprašanja o Hikoki C 6U3 Krožna žaga

Naša podporna ekipa išče uporabne informacije o izdelkih in odgovore na pogosta vprašanja. Če v pogosto postavljenih vprašanjih odkrijete nenatančnost, nam to sporočite prek obrazca za stik.

Koliko milimetrov mora žaga štrleti pod materialom, ki ga žagam? Potrjeno

Najbolje je, da ta ostane 3 mm ali več. Ko je manj, obstaja možnost, da se material sesuje ali povzroči grd rezultat.

To je bilo koristno (95) Preberi več

Ali moram pri uporabi krožne žage nositi zaščito za sluh? Potrjeno

Ja, moral bi. Čeprav se količina hrupa, ki ga proizvaja krožna žaga, med različnimi znamkami in modeli razlikuje, lahko dolgotrajna izpostavljenost glasnemu hrupu povzroči trajne poškodbe sluha. Zato je dobro nositi zaščito za sluh.

To je bilo koristno (43) Preberi več

Ali lahko električno orodje shranim v lopi ali garaži? Potrjeno

Na splošno lahko električno orodje shranite v lopi ali garaži, tudi če tam včasih zmrzne. Za življenjsko dobo električnega orodja pa je bolje, da ga hranite v suhem prostoru brez večjih temperaturnih nihanj. V lopi ali garaži lahko razlike v temperaturi povzročijo nastanek kondenza, ki lahko povzroči rjo. Poleg tega orodja, ki delujejo na baterije, delujejo krajše in se pri zelo nizkih temperaturah ne polnijo tako dobro. Da bi bili prepričani, kako je treba vaše električno orodje shraniti, vedno temeljito preberite uporabniški priročnik.

To je bilo koristno (13) Preberi več