Home > Naredi sam > Kotne brusilke > Hikoki Kotne brusilke > Hikoki G 18DBBL Kotna brusilka

Priročnik Hikoki G 18DBBL Kotna brusilka

Potrebujete priročnik za vaš Hikoki G 18DBBL Kotna brusilka? Spodaj si lahko brezplačno ogledate in prenesete PDF priročnik v slovenščini. Ta izdelek ima trenutno 4 pogosto zastavljeni vprašanji, 0 komentarjev in ima 0 glasov. Če to ni priročnik, ki ga želite, nas kontaktirajte.

Ali je vaš izdelek okvarjen in v priročniku ne najdete rešitve? Obiščite Repair Café za brezplačno popravilo.

Priročnik

English

b) Use power tools only with speciﬁ cally

designated battery packs.

Use of any other battery packs may create a risk of

injury and ﬁ re.

c) When battery pack is not in use, keep it away

from other metal objects, like paper clips, coins,

keys, nails, screws or other small metal objects,

that can make a connection from one terminal to

another.

Shorting the battery terminals together may cause

burns or a ﬁ re.

d) Under abusive conditions, liquid may be ejected

from the battery; avoid contact. If contact

accidentally occurs, ﬂ ush with water. If liquid

contacts eyes, additionally seek medical help.

Liquid ejected from the battery may cause irritation or

burns.

6) Service

a) Have your power tool serviced by a qualiﬁ ed

repair person using only identical replacement

parts.

This will ensure that the safety of the power tool is

maintained.

PRECAUTION

Keep children and inﬁ rm persons away.

When not in use, tools should be stored out of reach of

children and inﬁ rm persons.

SAFETY WARNINGS COMMON FOR

GRINDING OR ABRASIVE CUTTING-

OFF OPERATIONS

a) This power tool is intended to function as a

grinder or cut-oﬀ tool. Read all safety warnings,

instructions, illustrations and speciﬁ cations

provided with this power tool.

Failure to follow all instructions listed below may result in

electric shock, ﬁ re and/or serious injury.

b) Operations such as sanding, wire brushing or

polishing are not recommended to be performed

with this power tool.

Operations for which the power tool was not designed

may create a hazard and cause personal injury.

c) Do not use accessories which are not speciﬁ cally

designed and recommended by the tool

manufacturer.

Just because the accessory can be attached to your

power tool, it does not assure safe operation.

d) The rated speed of the accessory must be at least

equal to the maximum speed marked on the power

tool.

Accessories running faster than their rated speed can

break and ﬂ y apart.

e) The outside diameter and the thickness of your

accessory must be within the capacity rating of

your power tool.

Incorrectly sized accessories cannot be adequately

guarded or controlled.

f) Threaded mounting of accessories must match the

grinder spindle thread. For accessories mounted

by ﬂ anges, the arbour hole of the accessory must

ﬁ t the locating diameter of the ﬂ ange.

Accessories that do not match the mounting hardware of

the power tool will run out of balance, vibrate excessively

and may cause loss of control.

g) Do not use a damaged accessory. Before each use

inspect the accessory such as abrasive wheels for

chips and cracks, backing pad for cracks, tear or

excess wear, wire brush for loose or cracked wires.

If power tool or accessory is dropped, inspect for

damage or install an undamaged accessory. After

inspecting and installing an accessory, position

yourself and bystanders away from the plane of

the rotating accessory and run the power tool at

maximum no-load speed for one minute.

Damaged accessories will normally break apart during

this test time.

h) Wear personal protective equipment. Depending

on application, use face shield, safety goggles or

safety glasses. As appropriate, wear dust mask,

hearing protectors, gloves and workshop apron

capable of stopping small abrasive or workpiece

fragments.

The eye protection must be capable of stopping ﬂ ying

debris generated by various operations. The dust mask

or respirator must be capable of ﬁ ltrating particles

generated by your operation. Prolonged exposure to

high intensity noise may cause hearing loss.

i) Keep bystanders a safe distance away from work

area. Anyone entering the work area must wear

personal protective equipment.

Fragments of workpiece or of a broken accessory may

ﬂ y away and cause injury beyond immediate area of

operation.

j) Hold the power tool by insulated gripping surfaces

only, when performing an operation where the

cutting tool may contact hidden wiring.

Contact with a “live” wire will also make exposed metal

parts of the power tool “live” and could give the operator

an electric shock.

k) Position the cord clear of the spinning accessory.

If you lose control, the cord may be cut or snagged

and your hand or arm may be pulled into the spinning

accessory.

l) Never lay the power tool down until the accessory

has come to a complete stop.

The spinning accessory may grab the surface and pull

the power tool out of your control.

m) Do not run the power tool while carrying it at your

side.

Accidental contact with the spinning accessory could

snag your clothing, pulling the accessory into your body.

n) Regularly clean the power tool’s air vents.

The motor’s fan will draw the dust inside the housing and

excessive accumulation of powdered metal may cause

electrical hazards.

o) Do not operate the power tool near ﬂ ammable

materials.

Sparks could ignite these materials.

p) Do not use accessories that require liquid coolants.

Using water or other liquid coolants may result in

electrocution or shock.

KICKBACK AND RELATED

WARNINGS

Kickback is a sudden reaction to a pinched or snagged

rotating wheel, backing pad, brush or any other accessory.

Pinching or snagging causes rapid stalling of the rotating

accessory which in turn causes the uncontrolled power tool

to be forced in the direction opposite of the accessory’s

rotation at the point of the binding.

For example, if an abrasive wheel is snagged or pinched by

the workpiece, the edge of the wheel that is entering into the

pinch point can dig into the surface of the material causing

the wheel to climb out or kick out. The wheel may either jump

0000Book̲G18DBBL.indb30000Book̲G18DBBL.indb3 2017/12/0113:15:442017/12/0113:15:44

Ocena

Povejte nam, kaj menite o Hikoki G 18DBBL Kotna brusilka, tako da oddate oceno izdelka. Ali želite deliti svoje izkušnje z izdelkom ali postaviti vprašanje? Oddajte komentar na dnu strani.

Ali ste zadovoljni z Hikoki G 18DBBL Kotna brusilka?
Da Ne

Bodite prvi, ki boste ocenili ta izdelek

0 glasovi

Pridružite se pogovoru o tem izdelku

Tukaj lahko delite svoje mnenje o Hikoki G 18DBBL Kotna brusilka. Če imate vprašanje, najprej natančno preberite priročnik. Zahtevo za priročnik lahko opravite z uporabo našega kontaktnega obrazca.

Več o tem priročniku

Zavedamo se, da je lepo imeti papirni priročnik za vaš Hikoki G 18DBBL Kotna brusilka. Priročnik lahko vedno prenesete z naše spletne strani in ga natisnete sami. Če želite imeti originalni priročnik, priporočamo, da kontaktirate Hikoki. Morda bodo lahko zagotovili originalni priročnik. Ali iščete priročnik za vaš Hikoki G 18DBBL Kotna brusilka v drugem jeziku? Na naši domači strani izberite želeni jezik in poiščite številko modela, da preverite, ali je na voljo.

Specifikacije

Blagovna znamka	Hikoki
Model	G 18DBBL
Kategorija	Kotne brusilke
Vrsta datoteke	PDF
Velikost datoteke	13.23 MB

Vsi priročniki za Hikoki Kotne brusilke
Več priročnikov za Kotne brusilke

Pogosto zastavljena vprašanja o Hikoki G 18DBBL Kotna brusilka

Naša podporna ekipa išče uporabne informacije o izdelkih in odgovore na pogosta vprašanja. Če v pogosto postavljenih vprašanjih odkrijete nenatančnost, nam to sporočite prek obrazca za stik.

Na katerih površinah lahko uporabljam kotno brusilko? Potrjeno

Kotne brusilke so najprimernejše za uporabo na kovinah ali kamnu.Proizvajajo veliko toplote, zato so manj primerne za uporabo na lesu ali plastiki.

To je bilo koristno (63) Preberi več

Ali moram nositi zaščito za sluh pri uporabi kotne brusilnice? Potrjeno

Da, morali bi. Čeprav se količina hrupa, ki ga proizvaja kotna brusilka, med različnimi znamkami in modeli lahko razlikuje, lahko dolgotrajna izpostavljenost glasnemu hrupu povzroči trajne poškodbe sluha. Zato je dobro nositi zaščito za sluh.

To je bilo koristno (16) Preberi več

Ali moram pri uporabi kotne brusilne naprave nositi zaščito za oči? Potrjeno

Da. Majhni delci lahko med brušenjem poletijo navzgor. Ko ti zadenejo oko, lahko povzročijo trajne poškodbe oči. Zato je vedno treba nositi zaščito za oči.

To je bilo koristno (14) Preberi več

Ali lahko električno orodje shranim v lopi ali garaži? Potrjeno

Na splošno lahko električno orodje shranite v lopi ali garaži, tudi če tam včasih zmrzne. Za življenjsko dobo električnega orodja pa je bolje, da ga hranite v suhem prostoru brez večjih temperaturnih nihanj. V lopi ali garaži lahko razlike v temperaturi povzročijo nastanek kondenza, ki lahko povzroči rjo. Poleg tega orodja, ki delujejo na baterije, delujejo krajše in se pri zelo nizkih temperaturah ne polnijo tako dobro. Da bi bili prepričani, kako je treba vaše električno orodje shraniti, vedno temeljito preberite uporabniški priročnik.

To je bilo koristno (4) Preberi več