Priročnik Hoover HGH64SCP B Grelna plošča

Priročnik

07 GB

2.3. ADAPTING THE HOB TO DIFFERENT

TYPES OF GAS

To adapt the Hob for use with different types of gas, carry out the

following instructions:

•Remove the grids and burners

•Insert on hexagonal spanner (7 mm) into the burner support (Figure

7)

•Unscrew the injector and replace it with one suitable for the gas to be

used (see gas type table)

2.4. REGULATING THE MINIMUM FLAME

After lighting the burners, turn the control knob to the minimum setting

and then remove the knob (this can easily be removed by applying

gentle pressure).

Using a small «Terminal» type screwdriver the regulating screw can

be adjusted as in Figure 9. Turning the screw clockwise reduces the

gas flow, whilst turning it anticlockwise increases the flow – Use this

adjustment to obtain a flame of approximately 3 to 4 mm in length and

then replace the control knob.

When the gas supply available is LPG - the screw to set the idle flame

must be turned (clockwise) to the end stop.

When you have carried out the new gas regulation, replace the old gas

rating plate on your appliance with one (supplied with hob) suitable for

the type of gas for which it has been regulated.

3. USE OF HOB - USER INSTRUCTIONS

This appliance must only be used for the purpose for which it is

intended, domestic cooking, and any other use will be considered

improper and could therefore be dangerous. The Manufacturer will

not be responsible for any damage or loss resulting from improper

use.

3.1. USING THE GAS BURNER

To ignite the burners, place a lighted taper close to the burner, press in

and turn the control knob anti-clockwise.

If the burners have not been used for a couple of days, wait for a few

seconds before lighting the burner, this will allow any air present in the

pipes to escape.

For appliances fitted with electronic ignition carry out the following:

• Push in and turn the knob anticlockwise to the ignition symbol.

• İgnite the burner by pressing the sparker button.

For hobs fitted with automatic ignition simply push in and turn the knob

to the ignition symbol.

The ignition system will continue to generate sparks as long as the

control knob is being pressed.

If the burner has not ignited within 5 seconds, turn the knob to the 0

position and repeat the operation.

For models fitted with a safety tap (which cuts-off the flow of gas if the

flame is accidentally extinguished) the burners are ignited and

described above, but care must be taken.

Prior to switching on the gas hob ensure that the burners and burner

caps are correctly placed within their position.

GENERAL ADVISE

For best results, use cooking vessels with a flat surface. The size of

the surface should match the gas burner side as follows. Table A.

Burner Type

Ø pan/pot

(cm)

AUX

SR

R

UR

QC

12 - 18

18 - 24

24 - 26

24 - 28

24 - 28

Auxiliary

Semi Rapid

Rapid

Ultra Rapid

Double Ring

Table A

Power

(kW)

1,00

1,75

2,50

3,50

4,00

G20/20 mbar

(methane)

95 l/h

167 l/h

238 l/h

333 l/h

381 l/h

G30/28-30 mbar

(LPG)

73 g/h

127 g/h

182 g/h

255 g/h

291 g/h

These instructions are for qualified personnel, installation of equipment

must be in line with the relevant national standard. (For U.K. only: by law

the gas installation\commissioning must be carried out by a "Gas

Safe" installer)

All work must be carried out with the electricity supply disconnected.

The rating plate on the hob shows the type of gas with which it is designed to

be used. Connection to the mains gas supply or gas cylinder should be

carried out after having checked that it is regulated for the type of gas with

which it will be supplied. If it is not correctly regulated see the instructions in

the following paragraphs to change gas setting.

For liquid gas (cylinder gas) use pressure regulators which comply with the

relevant national standards.

Use only pipes,washers and sealing washers which comply with the

relevant national standards.

For some models a conic link is furnished to outfit for the installation in the

countries where this type of link is obligatory; in picture 8 it is pointed out

how to recognize the different types of links (CY = cylindrical, CO = conic).

In every case the cylindrical part of the link has to be connected to the hob.

2.2. GAS CONNECTION

4. MAINTENANCE AND CLEANING

Before cleaning the hob, ensure the appliance has cooled down.

Remove the plug from the socket or (if connected directly) switch off

the electricity supply.

Cleaning and user maintenance shall not be made by children without

supervision

Never use abrasives, corrosive detergents, bleaching agents or

acids. Avoid any acid or alkaline substances (lemon, juice, vinegar

etc.) on the enamelled, varnished or stainless steel sections.

When cleaning the enamelled, varnished or chrome sections, use

warm soapy water or a non caustic detergent. For stainless steel use

an appropriate cleaning solution.

The burners can be cleaned with soapy water. To restore their original

shine, use a household stainless steel cleaner. After cleaning, dry the

burners and replace.

It is important the Burners are replaced correctly.

Chromed grids and burners

Chromed grids and burners have a tendency to discolour with use.

This does not jeopardize the functionality of the hob.

Our After Sales Service Centre can provide spare parts if required.

For smaller containers the gas burner should be regulated so that the

flame does not overlap the base of the pan. Vessels with a concave or

convex base should not be used.

WARNING: If a flame is accidentally extinguished, turn the knob

to the off position and do not attempt to re-ignite if for at least 1

minute.

If over the years the gas taps become stiff to turn it is necessary to

lubricate them.

Such operation must be carried out only by qualified Service

Engineers.

5. AFTERCARE

Before calling out a Service Engineer please check the following:

• that the plug is correctly inserted and fused;

• that the gas supply is not faulty.

If the fault cannot be detected:

Switch off the appliance and call the After Service Centre. DO NOT

TAMPER WITH THE APPLIANCE.

24 - 28

Triple Crown

Burner

3,80

362 l/h

276 g/h

TC

Ocena

Več o tem priročniku

Zavedamo se, da je lepo imeti papirni priročnik za vaš Hoover HGH64SCP B Grelna plošča. Priročnik lahko vedno prenesete z naše spletne strani in ga natisnete sami. Če želite imeti originalni priročnik, priporočamo, da kontaktirate Hoover. Morda bodo lahko zagotovili originalni priročnik. Ali iščete priročnik za vaš Hoover HGH64SCP B Grelna plošča v drugem jeziku? Na naši domači strani izberite želeni jezik in poiščite številko modela, da preverite, ali je na voljo.

Specifikacije

Vsi priročniki za Hoover Grelne plošče
Več priročnikov za Grelne plošče

Pogosto zastavljena vprašanja o Hoover HGH64SCP B Grelna plošča

Naša podporna ekipa išče uporabne informacije o izdelkih in odgovore na pogosta vprašanja. Če v pogosto postavljenih vprašanjih odkrijete nenatančnost, nam to sporočite prek obrazca za stik.

Podobni izdelki

Priročnik

Hoover HHG6BRSX Grelna plošča

Priročnik

Hoover HGH 64SQCX Grelna plošča

Priročnik

Hoover HHW6LMX Grelna plošča

Priročnik

Hoover HHW6BR4TWA Grelna plošča

Priročnik

Hoover HGH64SXF C Grelna plošča

Priročnik

Hoover HIESC644D Grelna plošča

Priročnik

Hoover HGH 64SCB Grelna plošča

Priročnik

Hoover HGH 64SCX Grelna plošča

Sorodne kategorije