Priročnik Hoover SY71 SY02011 Sesalnik

Priročnik

3

*Certain Models Only ** Certain models only, nozzles may vary according to model

Emptying the Dust Container (Fig. 10)

1. Slide the bin release button downward and remove the dust bin from the cleaner.

2. Hold the container using the bin handle and pull the bin emptying latch. The dust

container door will automatically open.

3. Once empty, gently tap or shake the container to release any excess dust.

IMPORTANT -

Do not fill above the max level mark shown on the bin.

Allergy and asthma suerers:

When emptying any vacuum cleaner it is dicult to avoid exposure to dust. To minimize this

risk, please follow these instructions:

1. Wrap the lower bin in a plastic bag and close the bag tightly around the dust container

before emptying.

2. Pull the bin emptying latch to empty the dust into the plastic bag. Close the bag quickly

and dispose of it immediately. (Fig. 11)

Cleaning the washable lters Fig. 12

1. Slide the bin release button downward and remove the dust bin from the cleaner.

2. Remove the lter pack by releasing the tab at the rear.

3. Separate the GREY foam lter from the DARK GREY EPA lter pack using the tab provided.

Gently tap both lters against the side of a bin to release excess dust.

4. Wash the GREY foam lter thoroughly under hand warm water until the water runs clean.

Remove excess water by shaking and leave to dry for 24 hours. DO NOT USE HOT WATER

OR DETERGENTS.

5. Wash the DARK GREY EPA lter thoroughly from the inside under hand warm water until

the water runs clean. Remove excess water by shaking and leave to dry for 24 hours.

When completely dry reassemble and ret lters to cleaner. DO NOT USE HOT WATER OR

DETERGENTS.

CLEANER MAINTENANCE

IMPORTANT

- When using cleaning tools, the cleaner must be kept in the upright position, and

held.

Using your 3 in1 tool:

The 3 in1 tool (Fig.8) is composed of:

•Crevice tool to clean corners and hard to reach areas

 •Furniture nozzle to clean curtains and soft furnishings

 •Dustingbrushattachment(withbristles)tocleandelicatesurfaces

The 3 in1 tool can be used directly on the flexi tube or combined with the additional exten

sion tube.

Assembly the dust bin

(Fig. 9

):

• Dust bin to be put in the location

• To rotate the dust bin and lock into main body

IMPORTANT - For optimum performance, shake o excess dust from the lters regularly.

We recommend that the GREY foam lter and the DARK GREY EPA lter are washed every 3

MONTHS.

NOTE: Do not use the cleaner without lters assembled.

Cleaning the dust bin / separation unit

1. Place the bin on a at surface and remove the lters.

2. Remove the Airvolution system by lifting the Airvolution unit handle. (Fig. 13)

3. Use a cloth or the dusting brush to remove excessive dust from the Airvolution unit

surface.

4. Ret the Airvolution unit into the dust bin and ret the lters.

5. Ret the dust bin to the cleaner.

NOTE: For stubborn dirt the Airvolution system can be washed, but care must be taken that it

is completely dry before retting to the cleaner.

IMPORTANT -

For optimum performance, we recommend that Airvolution system is inspected

after each empty.

Removing a blockage

1. check if the dust container is full. If so refer to “emptying the dust container’’.

2. If the dust container is empty but suction is still low:

A.Ifcleaningtoolswereinusecheckthecleaningtool.(Themini-turbo*nozzlecanbe

checkedbyunlockingtheclipandliftingthecovertoremoveanyblockage) (Fig. 3b)

B. check the exi tube by removing it from the hose handle location, stretching it to full

length.

C. Check the bin inlet by removing the bin and checking inside the bin inlet.

D. Remove the nozzle and check the nozzle connection.

E. Remove the blockage inspection hose and check from both sides. (Fig. 14)

IMPORTANT  Switch the cleaner o and remove the plug from the electricity supply before

checking cleaner.

GB

ACCESSORIES AND NOZZLES

To obtain the best performance and energy eciency

#1

it is recommended that the correct

nozzles are used for the main cleaning operations. These nozzles are indicated in the diagrams

by the letters GP, HF or CA.

A nozzle type GP can be used to clean both carpet and hard oor.

A nozzle type HF is suitable for use only on hard oor.

A nozzle of type CA is suitable for use only on carpet.

The other nozzles are accessories for specialist cleaning tasks and are recommended for

occasional use only.

It is important to note that this vacuum cleaner is supplied with an Energy Label as required by

EuropeanRegulation(EU)665/2013.

If the label shows a red prohibition circle on the left covering the carpet symbol, then this

Ocena

Več o tem priročniku

Zavedamo se, da je lepo imeti papirni priročnik za vaš Hoover SY71 SY02011 Sesalnik. Priročnik lahko vedno prenesete z naše spletne strani in ga natisnete sami. Če želite imeti originalni priročnik, priporočamo, da kontaktirate Hoover. Morda bodo lahko zagotovili originalni priročnik. Ali iščete priročnik za vaš Hoover SY71 SY02011 Sesalnik v drugem jeziku? Na naši domači strani izberite želeni jezik in poiščite številko modela, da preverite, ali je na voljo.

Specifikacije

Vsi priročniki za Hoover Sesalniki
Več priročnikov za Sesalniki

Pogosto zastavljena vprašanja o Hoover SY71 SY02011 Sesalnik

Naša podporna ekipa išče uporabne informacije o izdelkih in odgovore na pogosta vprašanja. Če v pogosto postavljenih vprašanjih odkrijete nenatančnost, nam to sporočite prek obrazca za stik.

Podobni izdelki

Priročnik

Hoover HG530H 011 Sesalnik

Priročnik

Hoover HF916BF 011 Sesalnik

Priročnik

Hoover HF920P 001 Sesalnik

Priročnik

Hoover HF522STH 011 Sesalnik

Priročnik

Hoover HE320PET 011 Sesalnik

Priročnik

Hoover HF522NPW 011 Sesalnik

Priročnik

Hoover HF910H 011 Sesalnik

Priročnik

Hoover HF522LCG 011 Sesalnik

Sorodne kategorije